| Wood - Metal - Concrete - EPDM - & More |
|---|
| Cured: Any concrete must be sufficiently cured to have complete hydration, approximately 28 days depending on temperatures & humidity. |
| Sound: Dura-Rubber should not be placed on flaking concrete, spalling concrete. Surfaces exhibiting delamination, divots, spalls or any other surface anomalies, should be addressed by diamond grinding, shot blasting, or other mechanical methods leaving the surface properly profiled (see #3 below). Depending upon size of area, patching may be required prior to application of Dura-RubberTM. |
| Profiled: For a proper bond, the surface of concrete must be prepared in accordance with the standards established by theInternational Concrete Repair Institute (ICRI) Technical Guideline no. 03732 for Concrete Surface Profile (CSP). The established profile is categorized as CSP-1 through CSP-3. Customarily cement-based overlays do not require profiling. |
| Clean: After surface profiling is complete and prior to application of Dura-Rubber the surface must be free of any contaminants that serve as a bond breaker or prevent proper adhesion. This includes but is not limited to; dust, dirt, oil, grease, paints, glues, sealers, curing agents, efflorescence, chemical contaminants, rust, algae, mildew and other foreign matter. |
Limit Moisture: Since Dura-Rubber is not vapor permeable and due to the uncertainty of vapor barriers placed beneath concrete, testing prior to application is required.
a. Plastic sheet test (ASTM-D-4263) can often identify excessive moisture vapor transmission. Tape all 4 sides of an 18” (45 cm) square of clear plastic to the slab and leave in place for 16 hours. Any condensation formed or darkening of the slab beneath the plastic indicates the surface is too wet for polyurethane.
b. Calcium Chloride test (ASTM-F-1869) will quantify the amount of moisture that is transmitted to surface of the slab. The moisture measurement is expressed in terms of pounds (kg) per 1,000 ft2 (m2) per 24 hours. Measurements that are in excess of 3 pounds per 1,000 ft2 (1.4 kg per 100 m2) over 24 hours are too wet for polyurethane. Follow directions of test kit manufacturer.
c. Use a moisture meter moisture must be below 9%
Test in multiple locations
|
| PH Level: Do not apply Dura-Rubber when PH readings reading are above 10.5, typically this is found on freshly placed concrete before a cure of 28 days. |
| Curing" or "Vulcanization" TimesYou will notice the product is dry to the touch with-in a few hours, and will be waterproof. However, the rubber is still going through a very important process called "Vulcanization" - this is the process where the rubber becomes one single membrane and can contain water on a continuous basis. The process of "Vulcanization" takes 7 days. You do not want to expose coating to chemicals or continuous water saturation until the vulcanization process is complete. |
| DISPOSAL: Contact your local government household hazardous waste coordinator for information on disposal of unused product. Upon curing, left over catalyzed product is not hazardous. |
| Application:Rates of Application are typical:Mixing Dura-Rubber with crumb rubber mix. Mix 1-1/2 to 3 pounds of crumb rubber mix to 1-gallon Dura-Rubber (any color) depending on how thick you want to apply. Make sure to break up and lumps in the crumb rubber from packing. Mix well with a drill motor and paddle. Let sit for 15 min before using. If too thick or more open time, add up to 4 oz of Propylene Glycol per gallon of Dura-rubber.5 gallon High build a premix of 2 pounds crumb mix to 1 gallon of dura-rubber. Can be further thickened with 1 pound per gallon for a trowel applications. Apply one coat primer at the rate of 300-400sf per gallon.Pour the mixture around the floor and spread it with a magic trowel once the floor is covered. Clean the trowel with a rag and smooth out coating by pulling the trowel towards you. Clean trowel as necessary to prevent dragging. If you get any cracks in the coating once dry, using a putty knife, fill the cracks with the coating mixture. Apply coating 20 dry mil.For best results, apply using magic trowel.Additional coats can be applied depending on the thickness desired.You can apply a coat of straight Dura-rubber for a solid color.Apply two coats of sealer after 4-5 days cure time. |
Drying:
Needs to "deep" dry between application coats. This means that because Dura-Rubber is water-based, all water must evaporate out of each application coat prior to the next application coat. Otherwise, the rubber will develop small bubbles of fluid between the coats. If you have small bubbles appearing on your project, you need to wait longer between your application coats. Time to dry between applications coats is approximately 3-8 hours - depending on temperature and relative humidity |
SECOND COAT & AND TOP COAT:
Surface Preparation for additional or subsequent coats or topcoat: Optimal window of time to apply subsequent coats, or the top coat, is within 12- 48 hours. This will allow for a chemical bond. Apply additional coats at the rate of no more than 10 wet mils per coat |
SUITABILITY SAMPLE:
Because job site conditions and requirements can vary significantly, always prepare a sample on site. The sample should determine the adhesion to the concrete you can test one of two ways.1. Apply a 12x12 thin coat. Let dry for 24 hours minimum With a utility knife cut an X in the coating. Firmly stick some duct tape to the coating and pull the tape off. If it dees not remove the coating you are good to apply. We recommend you do this in a few areas.2. Cut a 6" long piece of reinforcement fabric and using the Dura-Rubber glue one end the the concrete making a flap. Let dry for a minimum of 24 hours the longer the stronger it we be. Pull on the tab to test adhesion. |
CLEAN-UP:
Before Dura-Rubber dries; spills and tools can be cleaned up with a soap and water. If it drys you will most likly have to dispose of the tool. |
DISPOSAL:
Contact your local government household hazardous waste coordinator for information on disposal of unused product. Upon curing, left over catalyzed product is not hazardous. |
WARRANTY:
Warranty of this product, when used according to the directions, is limited to refund of purchase price, or replacement of product (if defective), at manufactures/ seller’s option. Rubberizeit shall not be liable for cost of labor or direct and/or incidental consequential damages. |
CAUTIONSKEEP OUT OF REACH OF CHILDREN.
Although Dura-Rubber is non-toxic and low voc it is recommended to when prolonged breathing of vapors. Use NIOSH approved mask for organic vapors if threshold limit values are unsafe. Skin Contact: Skin contact may cause irritation.Remove contaminated clothing and wash affected skin with soap and water. Launder clothing before reuse. If symptoms persist, seek medical attention. Eyes: Wear safety eye protection when applying. Contact with eyes may cause irritation. Flush eyes with water for 15 minutes. If symptoms persist, seek medical attention. |
